Gitiles
Code Review Sign In
gerrit.onosproject.org / routing / 52a9cf841b9b7250c2e8f6c03e6d8da0eda9a76d / . / trellis
tree: cf08a0fb4ed017e96ae0b3059e95cd1926d906a9 [path history] [tgz]
  1. README.md
  2. bgpdbgp1.conf
  3. bgpdr1.conf
  4. dhcpd.conf
  5. trellis.json
  6. trellis.py
  7. trellis_dualhome.json
  8. trellis_dualhome.py
  9. trellis_remote_dhcp.json
  10. trellis_remote_dhcp.py
  11. trellis_vlan.json
  12. trellis_vlan.py
  13. trellislib.py
  14. zebradbgp1.conf
trellis/README.md

Trellis Leaf-Spine Fabric

Introduction

This folder contains Mininet scripts and corresponding config files that can be used to emulate Trellis leaf-spine fabric, vRouter and DHCP relay.

Download

git clone https://gerrit.onosproject.org/routing

Installation

Ubuntu 16.04 LTS

Some dependencies need to be installed for a fresh Ubuntu.

sudo apt-get update
sudo apt-get install gawk texinfo python-pip
sudo pip install ipaddress

Mininet

sudo apt-get install mininet

OpenvSwitch

Mininet should install OVS for you. Please run sudo ovs-vsctl --version and make sure the OVS version is above 2.5.0+.

DHCP server

sudo apt-get install isc-dhcp-server

Quagga

Trellis needs a special FPM patch for Quagga.

wget http://download.savannah.gnu.org/releases/quagga/quagga-0.99.23.tar.gz
wget https://wiki.opencord.org/download/attachments/1278529/fpm-remote.diff
tar -xzvf quagga-0.99.23.tar.gz
cd quagga-0.99.23
patch -p1 < ../fpm-remote.diff
./configure --enable-fpm --sbindir=/usr/lib
make
sudo make install
cd ..

ONOS - Installation

Learn about how to setup ONOS at: https://wiki.onosproject.org/. After installation, the following ONOS apps need to be activated.

export ONOS_APPS=drivers,openflow,segmentrouting,fpm,dhcprelay,netcfghostprovider

ONOS - Network Config

onos-netcfg <onos-ip> routing/trellis/trellis.json

Update Controller IP

The location of ONOS controller needs to be updated in several places, including Mininet script and zebra config.

In routing/trellis/trellis.py

net.addController(RemoteController('c0', ip='192.168.56.11'))
net.addController(RemoteController('c1', ip='192.168.56.12'))
net.addController(RemoteController('c2', ip='192.168.56.13'))

In routing/trellis/zebrabgp1.conf

fpm connection ip 192.168.56.11 port 2620

Start Mininet Emulation

cd routing/trellis
sudo ./trellis.py

Verify Network Connectivity

In Mininet, run

  • h1 ping 10.0.99.2 to check IPv4 connectivity
  • h1v6 ping6 2000::9902 to check IPv6 connectivity

Troubleshooting

  • Services in the emulated hosts may still be alive if Mininet is not terminated properly. In that case, simply run the following command to clean up.
sudo killall -9 dhclient dhcpd zebra bgpd
sudo mn -c