ONOS+P4 Tutorial: Exercise 1

The goal of this exercise is to introduce P4 and P4Runtime support in ONOS, along with the tools to practically experiment with it. In this exercise we will see how the ONOS "pipeconf" mechanism allow one to re-use existing ONOS apps to provide basic forwarding capabilities in a pipeline-agnostic manner, i.e. independently of the P4 program.

To run this exercise you will need multiple terminal windows (or tabs) to operate with the CLI of Mininet, ONOS, and BMv2. We use the following convention to distinguish between commands of different CLIs:

  • Commands starting with $ are intended to be executed in the Ubuntu terminal prompt;
  • onos> for commands in the ONOS CLI;
  • mininet> for the Mininet CLI;
  • RuntimeCmd: for the BMv2 CLI.

Exercise steps

  1. On terminal window 1, start ONOS with a small subset of the apps by executing the following command:

    $ cd $ONOS_ROOT
    $ ONOS_APPS=proxyarp,hostprovider,lldpprovider ok clean
    

    The $ONOS_ROOT environment variable points to the root ONOS directory. The ok command is an alias to run ONOS locally in your dev machine. Please note that if this the first time you run ONOS on this machine, or if you haven't built ONOS before, it can take some time (5-10 minutes depending on your Internet speed).

    Once ONOS has started you should see log messages being print on the screen.

  2. On terminal window 2, activate the BMv2 driver and tutorial pipeconf via the ONOS CLI.

    1. Use the following command to access the ONOS CLI:

      $ onos localhost
      

      You should now see the ONOS CLI command prompt. For a list of possible commands that you can use here, type:

      onos> help onos
      
    2. Enter the following command to activate the BMv2 driver:

      onos> app activate org.onosproject.drivers.bmv2
      

      You should see the following message on the ONOS log:

      Application org.onosproject.drivers.bmv2 has been activated
      
    3. Enter the following command to activate the pipeconf:

      onos> app activate org.onosproject.p4tutorial.pipeconf
      

      You should see the following messages on the log:

      New pipeconf registered: p4-tutorial-pipeconf
      Application org.onosproject.p4tutorial.pipeconf has been activated
      

      Please note the specific name used for this pipeconf p4-tutorial-pipeconf. We will later use this name to tell ONOS to deploy that specific P4 program to the switches.

    4. To verify that you have activated all the required apps, run the following command:

      onos> apps -a -s
      

      Make sure you see the following list of apps displayed:

      org.onosproject.generaldeviceprovider ... General Device Provider
      org.onosproject.drivers               ... Default Drivers
      org.onosproject.proxyarp              ... Proxy ARP/NDP
      org.onosproject.lldpprovider          ... LLDP Link Provider
      org.onosproject.protocols.grpc        ... gRPC Protocol Subsystem
      org.onosproject.protocols.p4runtime   ... P4Runtime Protocol Subsystem
      org.onosproject.p4runtime             ... P4Runtime Provider
      org.onosproject.drivers.p4runtime     ... P4Runtime Drivers
      org.onosproject.hostprovider          ... Host Location Provider
      org.onosproject.drivers.bmv2          ... BMv2 Drivers
      org.onosproject.p4tutorial.pipeconf   ... P4 Tutorial Pipeconf
      
    5. (optional) Change flow rule polling interval. Run the following command in the ONOS CLI:

      onos> cfg set org.onosproject.net.flow.impl.FlowRuleManager fallbackFlowPollFrequency 5
      

      This command tells ONOS to check the state of flow rules on switches every 5 seconds (default is 30). This is used to obtain more often flow rules stats such as byte/packet counters. It helps also resolving more quickly issues where some flow rules are installed in the ONOS store but not on the device (which can often happen when emulating a large number of devices in the same VM).

  3. On terminal window 3, run Mininet to set up a topology of BMv2 devices.

    1. To run Mininet, use the following command:

      $ sudo -E mn --custom $BMV2_MN_PY --switch onosbmv2,pipeconf=p4-tutorial-pipeconf --controller remote,ip=127.0.0.1
      

      The --custom argument tells Mininet to use the bmv2.py custom script to execute the BMv2 switch. The environment variable $BMV2_MN_PY points to the exact location of the script (you can use the command echo $BMV2_MN_PY to find out the location).

      The --switch argument specifies the kind of switch instance we want to run inside Mininet. In this case we are running a version of BMv2 that also produces some configuration files used by ONOS to discover the device (see steps below), hence the name onosbmv2. The pipeconf sub-argument is used to tell ONOS which pipeconf to deploy on all devices.

      The --controller argument specifies the address of the controller, ONOS in this case, which is running on the same machine where we are executing Mininet.

    2. A set of files are generated in the /tmp folder as part of this startup process, to view them (on a separate terminal window):

      $ ls /tmp/bmv2-*
      
    3. You will find ONOS netcfg JSON files in this folder for each BMv2 switch, open this file up, for example:

      $ cat /tmp/bmv2-s1-netcfg.json
      

      It contains the configuration for (1) the gRPC server and port used by the BMv2 switch process for the P4Runtime service, (2) the ID of pipeconf to deploy on the device, (3) switch ports details, and other driver-specific information.

      This file is pushed to ONOS automatically by Mininet when executing the switch instance. If everything went as expected, you should see the ONOS log populating with messages like:

      Connecting to device device:bmv2:s1 with driver bmv2
      [...]
      Setting pipeline config for device:bmv2:s1 to p4-tutorial-pipeconf...
      [...]
      Device device:bmv2:s1 connected
      [...]
      
    4. Check the BMv2 switch instance log:

      $ less /tmp/bmv2-s1-log
      

      By scrolling the BMv2 log, you should see all P4Runtime messages received by the switch. These messages are sent by ONOS and are used to install table entries and to read counters. You should also see many PACKET_IN and PACKET_OUT messages corresponding to packet-in/out processed by the switch and used for LLDP-based link discovery.

      Table entry messages are generated by ONOS according to the flow rules generated by each app and based on the P4Info associated with the p4-tutorial-pipeconf.

      If you prefer to watch the BMv2 log updating in real time, you can use the following command to print on screen all new messages:

      $ bm-log s1
      

      This command will show the log of the BMv2 switch in Mininet with name "s1".

      If needed, you can run BMv2 with debug logging enabled by passing the sub-argument loglevel=debug when starting Mininet. For example:

      $ sudo -E mn [...] --switch onosbmv2,loglevel=debug,pipeconf=p4-tutorial-pipeconf [...]
      

      Debug logging in BMv2 is useful to observe the life of a packet inside the pipeline, e.g. showing the header fields extracted by the parser for a specific packet, the tables used to process the packets, matching table entries (if any), etc.

    5. Check the flow rules inserted by each app in ONOS. In the ONOS CLI type:

      onos> flows -s
      

      You should see 3 flow rules:

      deviceId=device:bmv2:s1, flowRuleCount=3
          ADDED, bytes=0, packets=0, table=0, priority=40000, selector=[ETH_TYPE:arp], treatment=[immediate=[OUTPUT:CONTROLLER], clearDeferred]
          ADDED, bytes=0, packets=0, table=0, priority=40000, selector=[ETH_TYPE:bddp], treatment=[immediate=[OUTPUT:CONTROLLER], clearDeferred]
          ADDED, bytes=0, packets=0, table=0, priority=40000, selector=[ETH_TYPE:lldp], treatment=[immediate=[OUTPUT:CONTROLLER], clearDeferred]
      

      These flow rules are installed automatically for each device by the Proxy ARP and LLDP Link Discovery apps. The first one is used to intercept ARP requests (selector=[ETH_TYPE:arp]), which are sent to the controller (treatment=[immediate=[OUTPUT:CONTROLLER]), who in turn will reply with an ARP response or broadcast the requests to all hosts. The other two flow rules are used to intercept LLDP and BBDP packets (for the purpose of link discovery).

      These flow rules appear to be installed on table "0". This is a logical table number mapped by the pipeconf's interpreter to the P4 table named t_l2_fwd in mytunnel.p4 (line 191).

      This mapping is defined in PipelineInterpreterImpl.java (line 103)

    6. Compare ONOS flow rules to the table entries installed on the BMv2 switch.

      We can use the BMv2 CLI to dump all table entries currently installed on the switch. On a separate terminal window type:

       $ bm-cli s1
      

      This command will start the CLI for the BMv2 switch in Mininet with name "s1".

      On the BMv2 CLI prompt, type the following command:

      RuntimeCmd: table_dump c_ingress.t_l2_fwd
      

      You should see exactly 3 entries, each one corresponding to a flow rule in ONOS. For example, the flow rule matching on ARP packets should look like this in the BMv2 CLI:

      ...
      **********
      Dumping entry 0x2000002
      Match key:
      * standard_metadata.ingress_port: TERNARY   0000 &&& 0000
      * ethernet.dst_addr             : TERNARY   000000000000 &&& 000000000000
      * ethernet.src_addr             : TERNARY   000000000000 &&& 000000000000
      * ethernet.ether_type           : TERNARY   0806 &&& ffff
      Priority: 16737216
      Action entry: c_ingress.send_to_cpu -
      ...
      

      Note how the ONOS selector [ETH_TYPE:arp] has been translated to an entry matching only the header field ethernet.ether_type, while the bits of all other fields are set as "don't care" (mask is all zeros). While the ONOS treatment [OUTPUT:CONTROLLER] has been translated to the action c_ingress.send_to_cpu.

      Important: The BMv2 CLI is a powerful tool to debug the state of a BMv2 switch. Type help to show a list of possible commands. This CLI provides also auto-completion when pressing the tab key.

  4. It is finally time to test connectivity between the hosts of our Mininet network.

    1. On the Mininet prompt, start a ping between host1 and host2:

      mininet> h1 ping h2
      

      The ping should NOT work, and the reason is that we did not activate yet any ONOS app providing connectivity between hosts.

    2. While leaving the ping running on Mininet, activate the Reactive Forwarding app using the ONOS CLI:

      onos> app activate org.onosproject.fwd
      

      Once activated, you should see the the ping working. Indeed, this app installs the necessary flow rules to forward packets between the two hosts.

    3. Use steps 3.v and 3.vi to check the new flow rules.

      You should see 3 new flow rules.

      The Reactive Forwarding app works in the following way. It installs a low priority flow rule to intercepts all IPv4 packets via a send_to_cpu action ([OUTPUT:CONTROLLER] in ONOS). When a packet is received by the control plane, the packet is processed by the app, which in turn, by querying the Topology service and the Host Location service is ONOS, computes the shortest path between the two hosts, and installs higher priority flow rules on each hop to forward packets between the two hosts (after having re-injected that packet in the network via a packet-out).

  5. Congratulations, you completed the first exercise of the ONOS+P4 tutorial!

Bonus exercise

As a bonus exercise, you can re-run Mininet with more switches and hosts to see how Exercise 1 works with a more complex topology.

  1. Quit the current Mininet topology. In the Mininet CLI type:

    mininet> exit
    
  2. Start a new Mininet topology with the following command:

    $ sudo -E mn --custom $BMV2_MN_PY --switch onosbmv2,pipeconf=p4-tutorial-pipeconf --topo tree,3 --controller remote,ip=127.0.0.1
    

    By using the argument --topo we are telling Mininet to emulate a Tree topology with depth 3, i.e. with 7 switches, 6 links, and 8 hosts.

    Important: due to the limited resources of the VM, when executing many switches in Mininet, it might happen that some flow rules are not installed correctly on the switch (showing state PENDING_ADD when using ONOS command flows). In this case, ONOS provides an automatic reconciliation mechanism that tries to re-install the failed entries. To force ONOS to perform this process more often, make sure to apply step 2.v.

  3. If the Reactive Forwarding app is still running (see step 4.ii), you can ping all hosts in the network using the following Mininet command:

    mininet> pingall
    

    If everything went well, ping should work for every host pair in the network.

  4. You can visualize the topology using the ONOS web UI.

    Open a browser from within the tutorial VM (e.g. Firefox) to http://127.0.0.1:8181/onos/ui/. When asked, use the username onos and password rocks. You should see a nice tree topology.

    While here, feel free to interact with and discover the ONOS UI. For more information on how to use the ONOS web UI please refer to this guide: https://wiki.onosproject.org/x/OYMg

    To show or hide hosts, press the H key on your keyboard.

  5. Once done, to kill ONOS, press ctrl-c in the ONOS log terminal window. To quit Mininet, press ctrl-d in the Mininet CLI or type exit.